Application of Magnetic Materials Combined with Echo® Mass Spectrometry System in Analysis of Illegal Drugs in Sewage.

The aim of this study is to solve the problems of the complicated pretreatment and high analytical cost in the detection technology of trace drugs and their metabolites in municipal wastewater. A high-performance magnetic sorbent was fsynthesized for the enrichment of trace drugs and their metabolites in wastewater to develop a magnetic solid-phase extraction pretreatment combined with the acoustic ejection mass spectrometry (AEMS) analytical method. The magnetic nanospheres were successfully prepared by magnetic nanoparticles modified with divinylbenzene and vinylpyrrolidone. The results showed that the linear dynamic range of 17 drugs was 1-500 ng/mL, the recovery was 44-100%, the matrix effect was more than 51%, the quantification limit was 1-2 ng/mL, and the MS measurement was fast. It can be seen that the developed magnetic solid-phase extraction (MSPE) method is a good solution to the problems of the complicated pretreatment and analytical cost in the analysis of drugs in wastewater. The developed magnetic material and acoustic excitation pretreatment coupled with mass spectrometry analysis method can realize the low-cost, efficient enrichment, and fast analysis of different kinds of drug molecules in urban sewage.

Absorbing oxygen carriers promotes phosphorus recovery from sludge via the microwave thermal conversion process.

This study aims to apply the Absorbing oxygen carriers (AOCs) to induce the migration and transformation of phosphorus compounds during the microwave thermal conversion of sludge so the hard-to-extract organic phosphorus (OP) can be converted to easy-to-extract inorganic phosphorus (IP) and be enriched onto the sludge char. The AOCs were recycled by screen separation from the IP-rich sludge char, with the latter being a renewable phosphorus source from sludge. The AOCs in this novel process enhanced the conversion efficiency of OP into non-apatite inorganic phosphorus (NAlP), which was further converted to apatite inorganic phosphorus (AP). Most phosphorus in the sludge char is presented in the form of orthophosphate.

Magnetic iron oxide nanoparticle enhanced microwave pretreatment for anaerobic digestion of meat industry sludge.

Our study investigates the effects of iron oxide (Fe3O4) nanoparticles combined microwave pretreatment on the anaerobic digestibility and soluble chemical oxygen demand (SCOD) of meat industry sludge. One of our main objectives was to see whether the different microwave-based pretreatment procedures can enhance biogas production by improving the biological availability of organic compounds. Results demonstrated that combining microwave irradiation with magnetic iron oxide nanoparticles considerably increased SCOD (enhancement ratio was above 1.5), the rate of specific biogas production, and the total cumulative specific biogas volume (more than a threefold increment), while having no negative effect on the biomethane content. Furthermore, the assessment of the sludge samples' dielectric properties (dielectric constant and loss factor measured at the frequency of 500 MHz) showed a strong correlation with SCOD changes (r = 0.9942, R2 = 0.99), offering a novel method to evaluate pretreatment efficiency.

Treatment of chromium-containing sludge using sintering and ironmaking combined technology: A risk-reducing strategy for environmental impact.

The efficient, safe and eco-friendly disposal of the chromium-containing sludge (CCS) has attracted an increasing concern. In this study, Co-processing of CCS was developed via employing sintering and ironmaking combined technology for its harmless disposal and resource utilization. Crystalline phase and valence state transformation of chromium (Cr), technical feasibility assessment, leaching risk, characteristics of sintered products, and pollutant release during CCS co-processing were investigated through a series of laboratory-scale sintering pot experiments and large scale industrial trials. The results showed that the content of Cr(VI) in sintered products first increased then decreased with increasing temperature ranges of 300 °C-800 °C, and reached a maximum of 2189.64 mg/kg at 500 °C. 99.99% of Cr(VI) can be reduced to Cr(III) at above 1000 °C, which was attributed to the transformation of the Cr(VI)-containing crystalline phases (such as, MgCrO4 and CaCrO4) to the (Mg, Fe2+)(Cr, Al, Fe3+)2O4. The industrial trial results showed that adding 0.5 wt‰ CCS to sintering feed did not have adverse effects on the properties of the sintered ore and the plant's operating stability. The tumbler index of sinter was above 78% and the leaching concentrations of TCr (0.069 mg/L) was significantly lower than the Chinese National Standard of 1.0 mg/L (GB5085.3-2007). The TCr contents of sintering dust and blast furnace gas (BFG) scrubbing water were less than 0.19 wt‰ and 0.11 mg/L, respectively, which was far below the regulatory limit (1.5 mg/L, GB13456-2012). The mass balance evaluation results indicated that at least 89.9% of the Cr in the CCS migrated into the molten iron in the blast furnace (BF), which became a useful supplement to the molten iron. This study provided a new perspective strategy for the safe disposal and resource utilization of CCS in iron and steel industry.

Removal of pharmaceutical compounds and toxicology study in wastewater using Malaysian fungal Ganoderma lucidum.

Elevated usage of pharmaceutical products leads to the accumulation of emerging contaminants in sewage. In the current work, Ganoderma lucidum (GL) was used to remove pharmaceutical compounds (PCs), proposed as a tertiary method in sewage treatment plants (STPs). The PCs consisted of a group of painkillers (ketoprofen, diclofenac, and dexamethasone), psychiatrists (carbamazepine, venlafaxine, and citalopram), beta-blockers (atenolol, metoprolol, and propranolol), and anti-hypertensives (losartan and valsartan). The performance of 800 mL of synthetic water, effluent STP, and hospital wastewater (HWW) was evaluated. Parameters, including treatment time, inoculum volume, and mechanical agitation speed, have been tested. The toxicity of the GL after treatment is being studied based on exposure levels to zebrafish embryos (ZFET) and the morphology of the GL has been observed via Field Emission Scanning Electron Microscopy (FESEM). The findings conclude that GL can reduce PCs from <10% to >90%. Diclofenac and valsartan are the highest (>90%) in the synthetic model, while citalopram and propranolol (>80%) are in the real wastewater. GL effectively removed pollutants in 48 h, 1% of the inoculum volume, and 50 rpm. The ZFET showed GL is non-toxic (LC50 is 209.95 mg/mL). In the morphology observation, pellets GL do not show major differences after treatment, showing potential to be used for a longer treatment time and to be re-useable in the system. GL offers advantages to removing PCs in water due to their non-specific extracellular enzymes that allow for the biodegradation of PCs and indicates a good potential in real-world applications as a favourable alternative treatment.

The effect of carbonization temperature on textural properties of sewage sludge-derived biochars as potential adsorbents.

This article presents ways of recovering waste in the form of anaerobically digested and dried sewage sludge (average humidity approx. 6 wt%) by carbonization at various temperatures in the range of 400-900 °C. The resulting products, biochars, are investigated in terms of yield, surface properties and Raman spectra analysis. The sorption capacity of biochars differs depending on the carbonization temperature. The experimental amount of adsorbed CO2 slowly increases with the carbonization temperature from 0.212 mmol/g at 400 °C to the highest value of 0.415 mmol/g, which is achieved at 900 °C by slow carbonization at a rate of 10 °C/min. Additionally, there is a strong positive dependence of the adsorption capacity on the micropore volume. Higher carbonization temperatures support the powerful formation of micropores and improve their sorption capacity.

Electro-dewatering performance of sewage sludge under interrupted pulsating voltage: A comparison between square shape and half-sine shape waveform.

Electro-dewatering of sewage sludge with pulsating voltage was conducted under the two different wave shapes (square wave (SQW) and half-sine wave (HSW)) to investigate the influence of wave shape and duty cycle on sludge dewatering performance. The results indicated that, under the same average voltage, the moisture content of dewatered sludge with HSW was 10.3%-35.4% lower than that with SQW, suggesting the better dewatering performance of HSW. The optimal dewatering performance was achieved at duty cycle of 80% for SQW and 60% for SHW. The chemical oxygen demand of filtrate from HSW could be 13% higher than that from SQW, indicating the higher capacity of HSW in breaking sludge cells/floc structure. The applied voltage during electrochemical treatment promoted the hydrolysis of protein in filtrate, and the main components in the electro-dewatered filtrate were fulvic acid- and humic acid-like substances. The specific energy consumption for sludge electro-dewatering were 0.015-0.269 kWh/(kg removed water), and it was almost in linear relationship with duty cycle. By overall considering the energy consumption and electro-dewatering performance, the condition of 60% duty cycle with HSW was obviously better than other conditions, which provides a meaningful guidance for future application of sludge electro-dewatering technology with pulsating voltage.

Evaluating the efficacy of vermicomposted products in rain-fed wetland rice and predicting potential hazards from metal-contaminated tannery sludge using novel machine learning tactic.

The study assessed the ecotoxicity and bioavailability of potential metals (PMs) from tannery waste sludge, alongside addressing the environmental concerns of overuse of chemical fertilizers, by comparing the impacts of organic vermicomposted tannery waste, chemical fertilizers, and sole application of tannery waste on soil and rice (Oryza sativa L.) plants. The results revealed that T3, which received high-quality vermicomposted tannery waste as an amendment, exhibited superior enzymatic characteristics compared to tannery sludge amended (TWS) treatments (T8, T9). After harvesting, vermicomposted tannery waste treatment (T3) showed a more significant decrease in PMs bioavailability. Accumulation of PMs in rice was minimal across all treatments except T8 and T9, where toxic tannery waste was present, resulting in a high-risk classification (class 5 < 0.01) according to the SAMOE risk assessment. Results from Fuzzy-TOPSIS, ANN, and Sobol sensitivity analyses (SSA) further indicated that elevated concentrations of PMs (Ni, Pb, Cr, Cu) adversely impacted soil-plant health synergy, with T3 showing a minimal risk in comparison to T8 and T9. According to SSA, microbial biomass carbon and acid phosphatase activity were the most sensitive factors affected by PMs concentrations in TWS. The results from the ANN assay revealed that the primary contributing factor of toxicity on the TWS was the exchangeable fraction of Cr. Correlation statistics underscored the significant detrimental effect of PMs' bioavailability on microbial and enzymatic parameters. Overall, the findings suggest that vermicomposting of tannery sludge waste shows potential as a viable organic amendment option in the near future.

Recycling of sludge residue as a coagulant for phosphorus removal from aqueous solutions.

Phosphorus pollution poses a significant challenge in addressing water contamination. The coagulant is one of the effective methods to remove phosphorus from wastewater. Abundant Al and Fe oxides in sludge residue make it have great potential to synthesize water treatment coagulants. However, the utilization of sludge residue for preparation of coagulant was seldom investigated. In this study, we fabricated a novel coagulant, polyaluminum ferric chloride (SM-PAC), using sludge residue as a raw material through acid leaching and polymerization processes. Characterization results confirm that the parameters of SM-PAC meet the specifications outlined in the national standard (GB/T 22627-2022). We investigated the effects of pH, dosage, initial phosphorus concentration, and contact time on the removal efficiency of SM-PAC. As anticipated, the prepared SM-PAC exhibited a significant efficacy in removing phosphorus, meeting the discharge standards set for municipal sewage. Furthermore, the adsorption kinetics analysis suggests that the predominant mode of phosphorus adsorption on SM-PAC is chemical adsorption. Furthermore, the SM-PAC was employed in the actual wastewater treatment plant and exhibited excellent efficiency in phosphorus removal. The utilization of SM-PAC can not only effectively address the issue of sludge disposal but also achieve the goal of "treating waste with waste." It is expected that the proposed method of reusing sludge residue as a resource can provide a sustainable way to synthesize a coagulant for phosphorus removal.

Assessment of three different approaches for integrating phosphorus recovery from sewage sludge and derived products in existing wastewater treatment plants.

Three different technological solutions, namely acidogenic fermentation and chemical extraction (alkaline or acidic), followed by precipitation with 1% Ca(OH)2, were investigated in the view of integrating phosphorus recovery into existing wastewater treatment plants. Experiments were conducted at the lab-scale using (i) sludge taken from biologically and chemically promoted phosphorus removal activated sludge processes and (ii) ashes obtained from sludge muffle incineration. Results highlighted the benefits of enhanced biological phosphorus removal (EBPR) systems rather than chemically promoted phosphorus removal in not only phosphorus extraction (up to 40% with EBPR) and recovery directly from secondary sludge (P precipitation between 66 and 92%), but after sludge incineration as well (P extraction up to 96% and precipitation above 96%). Acidogenic fermentation ensured the highest phosphorus release from EBPR sludge (equal to a concentration in solution of 122 mg/L P-PO43-), while the derived ashes had a lower level of metal contamination (particularly Fe and Al content < 2%). The phosphorus-rich product obtained by means of the recovery process showed relevant metal contamination (Cu, Zn, and Ni) under some operating conditions, suggesting the need for further treatments.

Ionic liquid catalyzed low-temperature hydrothermal carbonization of sewage sludge to produce hydrochar with low heavy metal content and positive energy recovery.

An ionic liquid (IL, [DMAPA]HSO4) was prepared to facilitate the removal of heavy metals by hydrothermal carbonization (HTC) in sewage sludge (SS) and to obtain a positive energy recovery (ER, (Energyoutput/Energyinput - 1) > 0). The results found that the removal efficiencies of the Fe, Mn, Zn, Co, and Cd from SS exceeded 75 % with positive ER (6 %) at 20 wt% IL dosage (IL:SS). IL promoted the HTC reactions of proteins and polysaccharides to produce fixed carbon and small molecule polymers. The process mainly relies on IL to catalyze the dehydration and graphitization of SS and to destroy the heavy metal binding sites such as carboxyl and hydroxyl groups. Additionally, IL aids in constructing the macropore structures in hydrochar, thereby facilitating the release of heavy metals and water during the HTC process. This discovery holds promise for removing heavy metals from SS by one-pot HTC processes with positive energy recovery.

Characteristics of advanced anaerobic digestion sludge-based biochar and its application for sewage sludge conditioning.

The utilization of sludge-based biochar, characterized by abundant pore structures, proves advantageous in enhancing sludge dewatering performance. In this study, advanced anaerobic digestion sludge underwent pyrolysis to produce biochar, subsequently employed for sludge conditioning. Results revealed that biochar, obtained at 800 °C, exhibited the highest specific surface area (105.3 m2/g) and pore volume (0.17 cm3/g). As the pyrolysis temperature increased, the sludge's functional groups tended to aromatize. When used to condition sludge, particularly at a 20 % (dry solid) dosage, biochar significantly reduced sludge capillary suction time and floc size. The addition of biochar enhanced the conditioning effect of cationic polyacrylamide by absorbing extracellular polymeric substances, creating water molecule channels, and forming skeletons for sludge flocs. These findings introduce a novel approach to sludge reuse and provide valuable data supporting the use of biochar as a sludge conditioner.

Biochar from co-pyrolysis of biological sludge and woody waste followed by chemical and thermal activation: end-of-waste procedure for sludge management and biochar sorption efficiency for anionic and cationic dyes.

Nine biochars were produced by co-pyrolysis of sawdust and biological sludge following the "design of experiment" approach. Two kinds of sludge (both deriving from the treatment of mixed industrial-municipal wastewater) and two types of woody waste were selected as categorical predicting variables, while contact time, pyrolysis temperature, and sludge percentage were used as quantitative variables. Biochars were analysed for their product characteristics and environmental compatibility based on the European Standards (EN 12915-1:2009) for materials intended for water treatment (i.e. ash content, water leachable polycyclic aromatic hydrocarbons (PAHs) and elements), as well as for specific surface area (SSA), using them as response variables of a multivariate partial least square multiple regression, whose results provided interesting insights on the relationships between pyrolysis conditions and biochar characteristics. Biochars produced with sludge and/or providing the highest SSA values (258-370 m2 g-1) were selected to undergo a sustainable chemical treatment using a by-product of the gasification of woody biomass, complying in all cases with European Standards and achieving therefore the end-of-waste status for sewage sludge. The biochar deriving from the highest percentage of sludge (30% by weight) and with the highest SSA (390 m2 g-1) was thermally activated achieving SSA of 460 m2 g-1 and then tested for the sorption of direct yellow 50 and methylene blue in ultrapure water and real wastewater, compared to a commercial activated carbon (AC). The biochar showed Langmuir sorption maxima (Qm) 2-9 times lower than AC, thus highlighting promising sorption performances. Qm for methylene blue in wastewater (28 mg‧g-1) was confirmed by column breakthrough experiments.

Biochemical changes, metal content, and spectroscopic analysis in sewage sludge composted with lignocellulosic residue using FTIR-MIR and FTIR-NIR.

The use of lignocellulosic residues, originating from sawdust, in composting sewage sludge for organic fertilizer production, is a practice of growing interest. However, few studies have explored the effect of the proportion of sawdust and sewage sludge raw materials on composting performance in the humification process. This study assessed the addition of sawdust in the sewage sludge composting process, regarding carbon content, presence of heavy metals, and humification of the organic compost. The experimental design employed was a randomized complete block design with five treatments featuring different proportions of organic residues to achieve C/N ratios between 30-1 (T1: 100% sewage sludge and 0% sawdust, T2: 86% sewage sludge and 14.0% sawdust, T3: 67% sewage sludge and 33% sawdust, T4: 55% sewage sludge and 45% sawdust, and T5: 46.5% sewage sludge and 53.5% sawdust) and five replications, totaling 25 experimental units. The addition of lignocellulosic residue in sewage sludge composting increased the levels of TOC and the C/N ratio, reduced the levels of pH, P, N, Na, Ba, and Cr, and did not interfere with the levels of K, Ca, Mg, S, CEC, labile carbon, and metals Fe, Zn, Cu, Mn, Ni, and Pb. The increase in the proportion of sawdust residue favored the degradation of aliphatic groups, increasing the presence of aromatic structures and reducing humification at the end of composting. The use of sawdust as a lignocellulosic residue in sewage sludge composting is a viable and efficient alternative to produce high-quality organomineral fertilizers.

Resource utilization of drinking water treatment aluminum sludge in green cementing materials: Hydration characteristics and hydration kinetics.

As a byproduct of water treatment, drinking water treatment aluminum sludge (DWTAS) has challenges related to imperfect treatment and disposal, which has caused potential harm to human health and the environment. In this paper, heat treatment DWTAS as a supplement cementitious material was used to prepare a green cementing material. The results show that the 800°C is considered as the optimum heat treatment temperature for DWTAS. DWTAS-800°C is fully activated after thermal decomposition to form incompletely crystallized highly active γ-Al2O3 and active SiO2. The addition of DWTAS promoted the formation of ettringite and C-(A)-S-H gel, which could make up for the low early compressive strength of cementing materials to a certain extent. When cured for 90 days, the compressive strength of the mortar with 30% DWTAS-800°C reached 44.86 MPa. The dynamic process was well simulated by Krstulovic-Dabic hydration kinetics model. This study provided a methodology for the fabrication of environmentally friendly and cost-effective compound cementitious materials and proposed a "waste-to-resource" strategy for the sustainable management of typical solid wastes.

Ultrafiltration fractionation of potentially inhibitory substances of hydrothermal liquefaction aqueous phase derived from municipal sludge.

Hydrothermal liquefaction (HTL) is a promising thermo-chemical technology for municipal sludge treatment due to its potential for biocrude oil recovery and minimizing biosolids management costs. However, the process generates a high volume of an aqueous byproduct that needs to be treated due to its high chemical oxygen demand (COD) and various organic and inorganic compounds. Although the aqueous phase is known to contain recalcitrant and potentially inhibitory substances that may affect its biological treatment, their molecular weight distribution (MwD) and its impact on anaerobic biodegradability are poorly understood. Ultrafiltration (UF) was conducted to fractionate HTL aqueous into different molecular weight (Mw) fractions using 300, 100, 10, and 1 kDa membranes. Mesophilic biochemical methane potential (BMP) assays were conducted to assess the anaerobic biodegradability of each fraction, and the first-order model was used to calculate the degradation kinetics of potential inhibitory compounds. The highest percentage of organics (65 %) was found in the Mw<1 kDa range, whereas the 10>Mw>1 kDa had the lowest percentage (8 %). There was no significant difference in the cumulative specific methane produced from various Mw fractions (p>0.05). The Mw<1 kDa fraction had the highest first-order specific methane production rate (0.53 day-1), whereas the unfiltered HTL had the lowest (0.38 day-1). Although UF fractionation increased the rate of anaerobic degradation of HTL aqueous for the Mw<1 kDa fraction, the observed methane potential was only 55 % of the theoretical value. This implies that 45 % of COD remains undegraded even after permeation through the lowest Mw cut-off membrane. Therefore, further characterization of HTL aqueous is needed for compounds with molecular weights below 1 kDa to fully understand the nature of inhibitory organics and their impact on anaerobic digestion. Furthermore, pretreatments utilizing techniques such as adsorption and advanced oxidation may be necessary to enhance the specific methane yields from various HTL aqueous fractions, thereby bringing them closer to the theoretical yield.

Making waves: Riding the densification wave from current understanding to advancement.

Densification is a novel intensification strategy with the potential to improve treatment capacity within existing continuous-flow (CF) water resource recovery facilities at low capital and operating costs and at relatively small particle sizes compared to typical aerobic granular sludge (AGS) systems. To achieve densification, biological selection principles derived from selector design and AGS concepts have been coupled with physical selection via hydrocyclones at full-scale CF facilities to promote the growth and retention of granules. This combination lowers the sludge volume index (SVI) through superior sludge settling and paves the way for optimized nutrient removal and energy efficiency in low dissolved oxygen conditions. This paper sheds light on the benefits of densification. It delves into areas of advancement to further its implementation: hydrocyclone design, selector zone design, operational guidelines, and the target range for particle sizes and granule fractions.

Point-source tracking of microplastics in sewerage systems. Finding the culprit.

Prior microplastic (MP) research has focused more on the efficiency of removal techniques within wastewater treatment plants (WWTP), with comparatively less emphasis placed on identifying and understanding the sources of MPs. In this study, the presence of MP in wastewater from various sources and their associated WWTPs was investigated. Utilising focal plane array micro Fourier Transform Infrared spectroscopy (FPA-µFTIR), the chemical composition, size distribution, and mass of MPs were quantified. Notably, wastewater generated from an industrial laundry facility exhibited the highest MP concentration of 6900 counts L-1 or 716 µg L-1. Domestic sewage contained MP levels (1534 counts L-1; 158 µg L-1) similar to those at the WWTPs (1640 counts L-1; 114 µg L-1). Polyester was identified as a significant component in most of the sources, predominantly originating from the shedding of fibres during textile washing. Additionally, a post-processing software was employed to compare two methods for fibre identification: aspect ratio and elongation ratio. These findings underscore the potential environmental impact of domestic activities and laundry washing on wastewater MP content.

Leaching hazards of tire wear particles in hydrothermal treatment of sludge: Exploring molecular composition, transformation mechanism, and ecological effects of tire wear particle-derived compounds.

Tire wear particles (TWPs) are considered a significant contributor of microplastics (MPs) in the sludge during heavy rainfall events. Numerous studies have shown that hydrothermal treatment (HT) of sludge can accelerate the leaching of MP-derived compound into hydrothermal liquid, thus impairing the performance of subsequent anaerobic digestion and the quality of the hydrothermal liquid fertilizer. However, the leaching behavior of TWPs in the HT of sludge remains inadequately explored. This study examined the molecular composition of TWP-derived compounds and transformation pathways of representative tire-related additives under different hydrothermal temperatures using liquid chromatography-tandem mass spectrometry (LC-MS/MS) combined with mass difference analysis. The acute toxicity and phytotoxicity of TWP leachates were assessed using Vibrio qinghaiensis Q67 and rice hydroponics experiments. The results indicated that elevating the hydrothermal temperature not only amplified the leaching behavior of TWPs but also enhanced the chemical complexity of the TWP leachate. Utilizing both suspect and non-target screenings, a total of 144 compounds were identified as additives, including N-(1,3-dimethylbutyl)-N'-phenyl-p-phenylenediamine (6-PDD), hexa(methoxymethyl)melamine (HMMM), dibutyl phthalate (DBP). These additives underwent various reactions, such as desaturation, acetylation, and other reactions, leading to the formation of different transformation products (TPs). Moreover, certain additives, including caprolactam and 2,2,6,6-tetramethyl-4-piperidinol, demonstrated the potential to form conjugate products with amino acids or Maillard products. Meanwhile, TWP-derived compounds showed significant acute toxicity and detrimental effects on plant growth. This study systematically investigated the environmental fate of TWPs and their derived compounds during the HT of sludge, offering novel insights into the intricate interactions between the micropollutants and dissolved organic matter (DOM) in sludge.

Effects of pH-varying thermal modification on sewage sludge: A focus on releasing nitrogen- and phosphorus-containing substances.

Sewage sludge is promising for the recovery and utilisation of nutrient components, but its complex nature hinders the release of these components. The combination of pH and thermal modifications shows promise for the release of nutrient components from sludge. However, comprehensive studies on the full spectrum of pH levels and corresponding mechanisms of pH-varying thermal modification are lacking. In this study, the main nutrient components, physicochemical properties, molecular structure, and noncovalent interactions of sludge were comprehensively investigated through pH-varying thermal modification (within a pH range of 2.0 to 12.0 under the same thermal condition). The experimental results showed that the release of main organics, particularly nitrogen (N)-containing organics, was well-fitted, with a tick-like function (R2: 0.74-0.96). The thermal protons exhibited a notable accumulative mutagenic effect on the N-containing organics release, while the thermal hydroxyl ions had a more direct effect, as revealed by the changes in multivalent metals and molecular structures with the protonation-deprotonation of carboxyl groups. The driving force for the release of N-containing organics was identified as the fluctuation of electrostatic interactions at the solid-liquid interface of the sludge. However, the release of phosphorus (P)-containing substances exhibited a contrasting response to that of N-containing substances with varying pH, likely because the reaction sites of thermal protons and thermal hydroxyl ions for P-containing substances were different. Moreover, high concentrations of thermal protons and hydroxyl ions collapsed the Lifshitz-van der Waals interactions of sludge, resulting in a decrease in viscoelasticity and binding strength. These propositions were further confirmed through statistical analyses of the main indicators of the main nutrient components, physicochemical properties, and noncovalent interactions of sludge. These findings can provide a basis for optimising characteristic-specific methods to recovery nutrient components (N/P) from sludge.